Use tweezers to pull down forward this whiter piece, pull out cartridge holder from the right. Then push cartridge holder to the left till it can't move. The plug on the power wire. Now cartridge holder belt will reset his place, and cartridge holder will stop at original right side. The problem on Installation: Main problems: 1 During printing, the red indicator light is on.
Settlement: The ink wire length can't be too long, adjust it to the right size. If ink wire is too long, it will crush the printer body during printing. During printing, pull out power wire, use hand to move cartridge holder to the right and then to the left, adjust wire length. If ink wire is too short, it will also cause red indicator light flashing during printing, you also need to adjust the length according to above step. If use softer or lighter wire, this problem can be reduced, but it will cause ink blocked problem.
If you can't well fix the rack, just please change with new sponge sticker. Long time no work on the printer: Main problems: 1 The printer has not been used for about one month, now it can't work as usual. Settlement: If long time no use on the printer, it may cause following three cases:? If external tank ink surface is lower than printer head, ink will flow back to the tank stronger than to the ink cartridges, so air bubble will result at ink cartridges when printing, you will find line missing.
When printer head at the original right side, if rubber seal can't well cover printer head, the air will come in and damage printer head, ink will be dry or oxygen. If put printer in the environment of high temperature, dry circumstances, or under direct sunshine, this will result in the ink in the wire or printer head to be volatilization, dry or oxygen.
Following measures will settle above problems, please do accordingly:? If you will not use printer for a long time, please print test sheet, you'd better print about 10 pages of four colour or six colour block, and be sure test result is good. Do print cleaning step, when cartridge holder at the original right side, pull out power wire, move cartridge holder to the left side by hand, use a wet mop to clean the rubber seal on right side of the printer carefully, then move back cartridge holder to the right side by hand.
Check ink surface in external tank, do not let ink surface lower than printer head. Store printer and continuous system in the environment without high temperature and direct sunshine. Air leak on ink cartridges: Main problems: 1 During use, one ink wire exist long air bubble 2 During use, all ink wire exist long air bubble Settlement: When installing continuous inking system, there will exist a little space with air bubble always under15cm , you no need to care about this, this is the result by the air temperature, when you printing, the air bubble will die away.
But if one wire line with very long air bubble, please check cartridge and wire connected jet, perhaps here is not well connected, you can check and connect it again.
If all ink wire exist long air bubble, this perhaps is air leak on ink cartridges, please check and change the ink cartridges most is the cartridges not well sealed 8.
Damage on cartridge chips: Main problems: 1 Ink indicator light is in red, it will not change after reopen 2 It is no use even you reset the chips by chip decoder machine 3 When press print head cleaning button, it is no work. Settlement: 1 For Epson printer, when you take out cartridges and re-install, it will result in line missing, you need do cleaning or testing procedures for several times.
Not well install ink cartridges? Not well fix the chips? Chip pin on the cartridge holder is deformed? Chips have been damaged When you well install the cartridges and fix the chips, you can settle first and the second case, but for the third case, it results by taking out the cartridge without the well-fixed chip in rude, you need to ask maintenance person to take out print head, adjust chip pin or change a new one. For fourth cases, it happens when you use chip decoder to reset the chips, and you can use another chip decoder to have a try, if no use, you can only change the chips.
Continuous inking system is equipped with permanent chips, you no need to take out the cartridges for chip decode, so it much reduces the possibility of chip damage. The cartridge design on other units tend only to have a single head seal or rubber style seal which leak over time. We have developed our cartridges to ensure ink flow is even and consistent. Read more on our FAQ's page. All our CISS are shipped with a full hard copy of our installation manual included in the box.
Visit our Youtube channel for video instructions on selected models. Brother Resetters. TR TR Use keywords to find the product you are looking for. Advanced Search. Photo Pro ml Red R How to install ciss on ip ip ip and more. Pdf file. How to install ciss on mg mg mg and more. How to install ciss on canon Ix video. How to install ciss on mg mg.
0コメント